Spunbond Four Beam SSSS Line

Four Beam SSSS Spunbond Nonwoven Making Machine Technical Specification

PRODUCTION LINE OVERVIEW

This nonwoven fabric making machine is used for the production of non woven fabrics through the process of PP spinning, web forming, and thermal bonding. It primarily uses PP as the main raw material, along with additives such as color master batch, antioxidants, anti-pilling agents, and flame retardants. The production line is capable of producing PP spunbond non woven fabrics of different colors, properties, and suitable for various applications. This production line can produce both three-layer SSSS PP spunbond products , which can be converted according to different market positioning and customer needs.

SSSS sorting: S1 → S2 → S3→ S4 from the web forming machine to the direction of the calender.

GENERAL REQUIREMENTS OF THE MAIN EQUIPMENT OF SPUNBOND SYSTEM

1.Dosing system (4 sets )

Each system uses negative pressure suction type automatic feed.The feeding pipe is made of stainless steel with 1mm wall thickness. The dosing system provides the process interface to the operating interface of the host equipment for inquiry, and the fault alarm of the dosing system is output to the console of the host equipment for easy checking.

2.Screw extruder (4 sets)

Function and composition of the equipment: this device is mainly to squeeze and melt the PP chips, composed of transmission gear, reducer, screw, mixing head, sleeve, ceramic heater, frame, etc., and it’s equipped with automatic temperature control, cooling system and alarm system. The main transmission adopts AC frequency conversion control. The temperature control of each area adopts the temperature control module, solid state relay and Pt 100 platinum thermistor to form a temperature control closed-loop system.

3.Extruder for recycling materials: (4 sets)

Equipment function and composition: for edge material recycling. It consists of screw, sleeve, discharge head,

melt filter, transmission device, heating system, thermal insulation device, frame, temperature and pressure control system, edge material feeding roller and guide wheel device, etc...

4.Melt filter (4 sets)

Connected the extruder directly with the flange, composed of two sets of filter units.

5.Spin pump and drive (4 sets)

Type: gear pump

6.Spinning die body (4 sets, CL Latest Design)

Equipped with an automatic heating and insulation system and a pressure display control system behind the screen (referring to the filter screen), each zone's temperature control adopts a temperature control module, solid-state relay, and PT100 platinum thermistor to form a temperature control closed-loop system. Each spinning box can distribute the melt symmetrically and evenly; Equipped with specialized tools and transportation devices for easy replacement of components.

7.Monomer suction device (4 sets, CL Latest Design)

Double row and parallel with multiple tubes.

8.Quench chamber device (4 sets, CL Latest Design)

Adopting a new type of cross air blowing structure, the main frame is made of aluminum material, and stainless-steel sealing plate with insulation.

9.Stretching Unit (4 sets, CL Latest Design)

Adopts a new stretching air duct structure with thermal insulation.

The cover plate is made of 2mm steel plate, which is required to be easy to disassemble and assemble.

10 Diffuser (4 sets, CL Latest Design)

The width of diffusion duct can be adjusted online.

10.Web former (1 set, CL Latest Design)

Spin belt: two Pieces

One for use during commissioning, And the other one for use after commissioning is complete

11.Hot pressing roller (4 sets)

Driving mode: Passive

12.Support roller (4 sets)

The hardness of the rubber layer on the surface shall not be lower than SHA76.

The roller surface is treated with rubber coating. The roller body is treated with mid convex treatment.

Surface hardness: Shore hardness is about 70. Using grease lubrication.

13.Driving system (1 set)

The driving bearing adopts NSK or SKF brand, with a journal of 90mm.

Main driving roller: The roller surface is treated with rubber.

14.Structure of the web former:

Wall panel thickness is 80mm. Protection with cover plates on both sides. Ensure the parallelism of the axis of all rollers and the verticality of the center line of the web forming machine to achieve high-speed stability. All web forming bellows adopt a single side suction method.

15.Two-roll calender (1 set, CL brand)

Roller’s form: the upper roller is an embossing roller, and the lower roller is a smooth roller (S roller). The effective pattern width of the embossing roller is 3, 700mm. The width of the smooth roller is 3, 800mm.

16. Hydrophilic System With Dryer

Double-side Kiss Roll with oil distribution system.

The speed can be adjusted on control desk.

17. Winder (1 set)

Effective working width: 3, 700mm

18.Slitter (1 set)

Effective working width: 3, 700mm

Slitting width: 80mm-3,300mm